Series |
Model No. |
Output Watts |
Input Voltage |
Input Voltage range |
Polarity reverse protection |
220 |
STC-220600RDM |
600W continuous |
±220V DC |
±190V ~ ±260V DC |
By fuse |
ENVIRONMENTAL CONDITIONS: |
|
● Operating Temperature: | 0°C ~ +50°C Full Load |
● Output Power:
|
100% @ 50°C, 70% @ 60°C
|
● Operating Humidity: | 20%~85% RH. (Non condensing) (95% Optional)
|
● Storage Temperature | -20°C~+80°C
|
● Storage Humidity:
|
10%~90% RH. (Non condensing) |
● Operating Altitude | 10M Below Sea level and 3000M Above Sea level |
|
|
DC INPUT CHARACTERISTICS: |
|
● Input connector type | 30A/ 300V UL Approved Gold Plated Brass 1.2t/2-Pin Terminal
|
● Input Current
|
3.8A/2.9A (600W) @ Full Load High Line & Low Line |
● Inrush Current | Less than 20A Cold start @25°C ambient
|
|
|
DC OUTPUT CHARACTERISTICS:
|
|
Output Voltage |
Regulation |
Output Current |
Ripple & Noise |
|||
Load |
Line |
Cross |
600W |
|||
Min |
Max |
|||||
+5V |
±5% |
±1% |
±5% |
0A |
20A |
50mV |
+12V |
0A |
48.5A |
120mV |
|||
+3.3V |
0A |
20A |
50mV |
|||
-12V |
±8% |
0A |
0.5A |
120mV |
||
-5V(optional) | ±5% |
|
50mV | |||
+5VSB |
±5% |
0A |
3.5A |
50mV |
||
Maximum continuous combined load on +3.3 V & +5V DC output shall not exceed |
166 |
Wattage |
||||
Maximum continuous combined load on +3.3 V & +5V & 12V DC output shall not exceed |
582.5 |
|||||
Maximum continuous total DC output power shall not exceed |
600 |
OVERALL PERFORMANCE: | |
● Efficiency | 90% typical @220V DC Full Load |
● Hold up time
|
When power shut down DC output 5V must be maintain 1ms @220V DC
|
● Power Good Signal | TTL Compatible signal, on delay 100~500ms, off delay 1ms min |
● Short Circuit Protection (SCP)
|
All output equipped with SCP (shutdows and latch off)
|
● Over Power Protection (OPP) | Peak power protected to 130%±10% of continuous rated power |
|
(shutdown and latch off)
|
● Over Voltage Protection (OVP) | +3.3V@3.6V~4.3V, +5V@5.5V~6.5V, +12V@13.2V~15.6V |
|
|
RELIABILITY: |
|
● MTBF (Mean Time Between Failure): | 100 000 hours @max. Load, 220V DC & 25°C ambient
|
● Safety Standards | Meet IEC60950-1, EN60950-1 |
● Safety Approved |
|
● EMI Compatibility (EMC) Standard |
EN55032: 2015/AC: 2016, Class A; EN55035: 2017;
|
|
EN6100-3-3: 2013; IEC6100-4-4: 2012; IEC6100-4-5: 2014+A1: 2017;
IEC6100-4-6: 2013+CAR1: 2015; IEC6100-4-8: 2009; IEC6100-4-11: 2004+A1: 2017 |
|
|
ISOLATION:
|
|
● INPUT and OUTPUT are isolated by transformers and optical couplers
|
|
● Dielectric Withstand: | INPUT to OUTPUT: 3kV DC for 60 seconds |
● Dielectric Withstand: | INPUT to FRAME GROUND: 3kV DC for 60 seconds |
● Leakage Current: | <0.005μA @220V DC |
|
|
LED Indicator: |
|
● Power module 1: | Green LED when Power On |
● Power module 2: | Green LED when Power On
|
|
|
Alarm function: |
|
● In the rear panel with power failure alarm signal to indicate when power failure wire
|
|
|
|
Alarm reset switch: |
|
● To reset by switch
|
|
|
|
Output Connector specific: |
|
● ATX 24 Pin x 1: | Molex 29-01-2240 or equivalent |
● +12V(P4) 4 pin x 1: | Molex 39-01-2040 or equivalent |
● HDD, DVD 4 pin x 4: | Molex 8981-04P or equivalent |
● FDD 4 pin x 1: | AMP171822-4 or equivalent |
● Serial ATA x 4:
|
Molex 675820000 or equivalent |
● CPU EPS 8 Pins x 1:
|
Molex 39-01-2080 or equivalent |
● PCIe 12V 6+2 pin x 2
|
|
|
|
Standard Output Cable Length:
● 550mm ± 50mm / 21.6 inches
PCB specific:
● 6 layer
● Copper: 3 Oz each layer
● Thickness: 1.6 mm
● Material: FR4
● PCB material origin: Taiwan
Power chassis Dimension:
● 450(L) x 200(W) x 41.3(H) mm / 17.71(L) x 7.87(W) x 1.62(H) Inches
Note
● Power Supply is not able to be used in stand alone application
● Use Power Supply in Power Chassis Assembly only
DOWNLOAD_specification_RD_STC-220600RDM.pdf
DOWNLOAD_DRAWING_stc-rd-450-M-20240205-3.pdf